Есть одна микруха > 512K X 8 Bit CMOS 5.0 Volt-only, Uniform Sector Flash Memory В даташите имеется абзацы: Requirements for Reading Array Data To read array data from the outputs, the system must drive the CE and OE pins to VIL. CE is the power control and selects the device. OE is the output control and gates array data to the output pins. WE should remain at VIH all the time during read operation. The internal state machine is set for reading array data upon device power-up, or after a hardware reset. This ensures that no spurious alteration of the memory content occurs during the power transition. No command is necessary in this mode to obtain array data. Standard microprocessor read cycles that assert valid addresses on the device address inputs produce valid data on the device data outputs. The device remains enabled for read access until the command register contents are altered. See "Reading Array Data" for more information. Refer to the AC Read Operations table for timing specifications and to the Read Operations Timings diagram for the timing waveforms, lCC1 in the DC Characteristics table represents the active current specification for reading array data и Reading Array Data The device is automatically set to reading array data after device power-up. No commands are required to retrieve data. The device is also ready to read array data after completing an Embedded Program or Embedded Erase algorithm. After the device accepts an Erase Suspend command, the device enters the Erase Suspend mode. The system can read array data using the standard read timings, except that if it reads at an address within erase-suspended sectors, the device outputs status data. After completing a programming operation in the Erase Suspend mode, the system may once again read array data with the same exception. See "Erase Suspend/Erase Resume Commands" for more information on this mode. The system must issue the reset command to re-enable the device for reading array data if I/O5 goes high, or while in the autoselect mode. See the "Reset Command" section, next. See also "Requirements for Reading Array Data" in the "Device Bus Operations" section for more information. The Read Operations table provides the read parameters, and Read Operation Timings diagram shows the timing diagram. и рисунки. Как я понял, микросхема умеет при запуске автоматически без предъявления адресов выдавать байты. С какой частотой она будет их выдавать?
В прикрепленном треде спросить религия не позволяет?
не отвечают же
Бамп
Микросхема при запуске настроена на чтение. Времянку для чтения все равно нужно формировать.
>>201363как?
там же нет пина типа клок
А клок тебе и не нужен. Просто подаешь на WE высокий уровень, потом выставляешь адрес, потом подаешь на СЕ низкий уровень, потом подаешь на ОЕ низкий уровень. И через время tое у тебя будут на шине данных данные, записанные по выставленному адресу.
>>201462Я не про это, микросхема уже с заводской функцией read array data. Я попробывал его включить, она действительно сразу же начинает выдавать данные. Хотелось бы узнать частоту выдачи данных.
>>201463ОП-хуй, не фантазируй, что бы получить данные нужно выставить адрес. Если его не выставить получишь данные с рандомной ячейки. Read Array Data - CE = 0, OE = 0, WE = 1, если до этого ты не послал команду на чтение какого нибудь МаняID.
>>201436сокеты есть зато
>>201463Ну если ты включил питание и у тебя ноль на шине адреса, CE и OE, то и получишь данные с нулевого адреса. Или ты хочешь сказать, что данные меняются при неизменном адресе?